How to Guides

HOW DO I TURN ON/TURN OFF MY ECIG?

To switch the electronic cigarette on or off, press the button located on the battery 5 times in quick succession. A blue light will flash.

This is a standard safety mechanism so you do not accidentally leave it on it your pocket.

If you are trying to use your Electronic Cigarette and the light is flashing this may mean that your Clearomiser is screwed on too tight on the Battery, unscrew this slightly and try again.

HOW DO I FILL MY GSH2/GSH3 CLEAROMISER WITH E LIQUID?

GSH2/GSH3: The GSH2 and GSH3 Clearomisers are an advanced 3 piece set comprising of a BASE, WICK and a one piece CHAMBER. This Clearomiser boasts a completely sealed unit, and is Bottom fed.

To fill this with your ID Liquid, you need to remove the BASE from the bottom of the Clearomiser and pour your liquid down the SIDE of the CHAMBER.

Notice that as this is a one piece CHAMBER, a tube runs through the centre of the CHAMBER, therefore if you pour your E Liquid down the centre of the CHAMBER it will exit the CHAMBER, leaving you with no liquid in your clearomiser and a mess.

Once you have filled this to your desired level, firstly make sure that your WICK is securely screwed into the BASE and then screw the BASE back onto the CHAMBER, DO NOT over tighten the BASE onto the CHAMBER, this can cause damage to the Clearomiser, you are then ready to start vaping.

PLEASE NOTE ALL COMPONENTS MUST REMAIN ON THE CLEAROMISERS, DO NOT REMOVE ANY RUBBER SEALING RINGS “WASHERS” OR PIECES OF FABRIC, IF REMOVED THE WARRANTY IF VOID AND REPLACEMENTS MUST BE PURCHASED.

HOW DO I CHARGE MY EGO T or EVO D BATTERY?

1. Unscrew the Clearomiser from the Battery.

2. Wipe the Battery connection to clean the connection from any dust, dirt or E Liquid.

3. Screw the battery into the USB charger.

4. Connect the USB charger with the power source*

*The output of the Power Source must be suitable for the input of the USB Charging Cable. Please see reverse of charging cable for this information.

HOW DO I CHARGE MY EGO T or EVO D BATTERY?

To use your Electronic Cigarette, once you have pressed the Button 5 times to switch it on, hold down the power button to activate the Electronic Cigarette and vape away.

Once you have vaped your desired amount release the power button. The Electronic Cigarette will then return to Stand-by until your next vape.

Be careful not to inhale too hard or too fast as this may not produce enough vapour. When using your Electronic Cigarette for the first time, or after recharging, you should take a few quick puffs in order to prime the heating element contained within the Clearomiser.

We recommend:

  • Inhaling for a maximum of 8 seconds per inhale
  • Not inhaling excessively to prevent the liquid from overheating and burning
  • Allowing the clearomiser to cool for a few minutes after each vaping session and before refilling

If you are trying to use your Electronic Cigarette and the light is flashing this may mean that your Clearomiser is screwed on too tight on the Battery, unscrew this slightly and try again.

HOW DO I ORDER ECIGNATURE PRODUCTS?

Ordering is easy through our secure website.

Simply browse our range of Electronic Cigarettes, E Liquids and Accessories, going through all Steps available, then click ‘ORDER’ to Review all the items that you have selected and then click ‘ADD TO CART’.

When you’re ready to confirm your items, click on ITEMS at the top of the screen which is next to MY WISHLIST. This will take you to your CART.

If you have a Voucher/Coupon simply apply your code in “APPLY COUPON” and click APPLY COUPON, this will then deduct your discounted amount.

Once you are item with your items, click “PROCEED TO CHECKOUT”, this will then direct you to our billing page.

Here you must Register as a Customer to continue with your order, this enables you to receive order confirmation emails and any offers that are exclusive via email.

You then have to complete the Billing and Shipping details accordingly and double check your order.

Now that you are Registered Customer on your website, next time you order, simply log into our website using your username and password you created.

Finally, at the bottom of the Screen you must TICK the Terms and Conditions box then click “PROCEED TO PAYPAL”. This will direct you to the payments screen where you have the option to pay via PayPal or Credit/Debit card, which ever you prefer.

Ordering is that easy!

However, if you do have difficulty placing any orders give us a call on 0800 862 0264, during our opening hours, Monday – Friday 9am-5pm. We are always happy to help.

HOW DO I FILL MY CE5+ CLEAROMISER WITH E LIQUID?

CE5+: The CE5+ Clearomiser is a 4 piece set comprising of a BASE, a WICK, a CHAMBER and TIP. This is a top fed Clearomiser.

To fill this with your ID Liquid, you need to remove the TIP of the Clearomiser and pour your liquid down the CHAMBER. Once you have filled this to your desired level, place the TIP securely back onto your chamber.

Rotate your Clearomiser to ensure the ID Liquid is running throughout the chamber and then you are ready to vape.

PLEASE NOTE ALL COMPONENTS MUST REMAIN ON THE CLEAROMISERS, DO NOT REMOVE ANY RUBBER SEALING RINGS “WASHERS” OR PIECES OF FABRIC, IF REMOVED THE WARRANTY IF VOID AND REPLACEMENTS MUST BE PURCHASED.

HOW DO I FILL MY MINIPROTANK WITH E LIQUID?

Mini ProTank: The Mini Protank Clearomisers are an advanced 4 piece set comprising of a BASE, WICK, CHAMBER and TIP. This is also Bottom Fed.

To fill this with your ID Liquid, you need to remove the BASE from the Clearomiser and pour your Liquid down the SIDE of the CHAMBER.

Notice a Inner Tube runs through the center of the CHAMBER, therefore if you pour your E Liquid down the centre of the CHAMBER it will exit the CHAMBER, leaving you with no Liquid in your Clearomiser and a mess.

Once you have filled this to your desired level, firstly make sure that your WICK is securely screwed into the BASE and then screw the BASE back onto the CHAMBER, DO NOT over tighten the BASE onto the CHAMBER, this can cause damage to the Clearomiser, you are then ready to start vaping.

PLEASE NOTE ALL COMPONENTS MUST REMAIN ON THE CLEAROMISERS, DO NOT REMOVE ANY RUBBER SEALING RINGS “WASHERS” OR PIECES OF FABRIC, IF REMOVED THE WARRANTY IF VOID AND REPLACEMENTS MUST BE PURCHASED.

HOW DO I FILL MY BCC TANK WITH E LIQUID?

BCC Tank: The BCC Tank Clearomisers are an advanced 4 piece set comprising of a BASE, WICK, CHAMBER and TIP. This is also Bottom Fed.

To fill this with your ID Liquid, you need to remove the BASE from the Clearomiser and pour your Liquid down the SIDE of the CHAMBER.

Notice a Inner Tube runs through the center of the CHAMBER, therefore if you pour your E Liquid down the centre of the CHAMBER it will exit the CHAMBER, leaving you with no Liquid in your Clearomiser and a mess.

Once you have filled this to your desired level, firstly make sure that your WICK is securely screwed into the BASE and then screw the BASE back onto the CHAMBER, DO NOT over tighten the BASE onto the CHAMBER, this can cause damage to the Clearomiser, you are then ready to start vaping.

PLEASE NOTE ALL COMPONENTS MUST REMAIN ON THE CLEAROMISERS, DO NOT REMOVE ANY RUBBER SEALING RINGS “WASHERS” OR PIECES OF FABRIC, IF REMOVED THE WARRANTY IF VOID AND REPLACEMENTS MUST BE PURCHASED.

HOW DO I FILL MY KAMRY X6-V2 TANK WITH E LIQUID?

Kamry X6-V2 Tank: The Kamry X6-V2 Tank is an advanced 4 piece set comprising of a CHAMBER, WICK, TOP and MOUTHPIECE. This is also a Top Fed Tank.

To fill this tank with your ID Liquid, you need to unscrew the metal TOP from the CHAMBER of the Tank.

Fill the Tank CHAMBER with your ID Liquid by tilting the chamber slightly, inserting the top of the Liquid Bottle and dripping the Liquid down the inside of the wall against the outer wall of the TANK.

DO NOT pour any liquid in the center tub i.e. the small pin hole opening.

Screw the top back on your Tank as comfortably as it will go and you will now be ready to start vaping.

PLEASE NOTE ALL COMPONENTS MUST REMAIN ON THE CLEAROMISERS, DO NOT REMOVE ANY RUBBER SEALING RINGS “WASHERS” OR PIECES OF FABRIC, IF REMOVED THE WARRANTY IF VOID AND REPLACEMENTS MUST BE PURCHASED.

HOW DO I KNOW WHEN MY EGO T or EVO D BATTERY NEEDS RECHARGING?

If you press the power button the the Battery and it flashes numerous times, this indicates the the Battery needs charging.

HOW LONG DOES MY BATTERY TAKE TO CHARGE?

Using the portable charger case or a USB connection should takes around 2 hours to fully recharge a Battery.

When your Battery is fully charged the charger will turn Green.

HOW DO I PUT MY ELECTRONIC CIGARETTE BACK TOGETHER?

Once you have filled your Clearomiser with ID E Liquid, and screwed the BASE comfortably onto the CHAMBER, you will have 2 parts to your Electronic Cigarette:

1 x Battery

1 x Clearomiser

To put your Electronic Cigarette back together just simply Screw your Clearomiser onto the Battery tightly, DO NOT over tighten the Clearomiser onto the Battery as this will cause damage to both Battery and Clearomiser, screw until comfortably tightened.

You should then be ready to vape away.

WHY IS MY CLEAROMISER LEAKING E LIQUID?

If your Clearomiser is leaking, and it is over 4 weeks old, this may be because your Clearomiser Wicks needs replacing, if this is the case please purchase either a NEW Clearomiser or replacement wicks.

If your Clearomiser is within our 7 Day Warranty please follow these steps before continuing to our Returns Form:

GSH2 Clearomiser:

1. Unscrew the BASE from the CHAMBER.

2. Unscrew the WICK from the BASE.

Your Clearomiser should now be in 3 parts.

3. Check that all the Rubber Sealing Rings “Washers” are correctly placed on the wick. There should be a Rubber Sealing Ring “Washer” at the Bottom of the AERIAL like prong on the WICK this acts as PLUG to prevent any ID Liquid entering the inner tube of the Clearomiser.

4. Check that the WICKS (the tiny bits of fabric that now will be clear once in contact with ID E Liquid) are located on the WICK under the Rubber Sealing Ring “WASHER”. DO NOT Pull or Remove the WICK (fluffy fabric) this must stay securely inside its metal covering.

5. Carefully, wipe down the WICK with a tissue until dry, do not remove the Rubber Sealing Ring “WASHER” or Wicks.

6. Screw the WICK back onto the BASE, DO NOT over tighten as this will cause damage to both BASE and WICK, only tighten until comfortable.

7. Run your CHAMBER under a tap, through the Top (the mouthpiece) and the Bottom of the CHAMBER. To Clean the CHAMBER of any excess ID Liquid they may have entered the inner tube accidentally.

8. Pour some ID Liquid down the SIDE of your Clearomiser CHAMBER.

9. Screw the BASE onto the CHAMBER, again DO NOT over tighten as this will cause damage to both BASE and CHAMBER, only tighten until comfortable.

Notice that the Rubber Sealing Ring “Washer” acts as a PLUG, this prevents any ID Liquid entering the Inner Tube of the Clearomiser, stopping you from inhaling ID Liquid.

If your Clearomiser is still leaking please complete our Returns Form and a member of our Customer Team will be in contact with you.

Clearomisers are very reliable and leakproof by design if used correctly. The Clearomiser can leak under certain conditions:-

  • If the rubber sealing ring “Washer” on the wick has been lost
  • If placed in direct sunlight or in extreme heat ie) on the dashboard of a car or near a fire
  • If overfilled or incorrectly filled
  • If used excessively

PLEASE NOTE: IF THE WICKS OR RUBBER SEALING RINGS “WASHERS” HAVE BEEN REMOVED THE WARRANTY IS VOID AND REPLACEMENTS MUST BE PURCHASED.

WHY IS MY CLEAROMISER IS MAKING A BUBBLING SOUND?

This bubbling sound indicates that there is E Liquid clogged up within the centre tube of the CHAMBER.

To “unclog” or clean this part of the CHAMBER please follow these simple steps:

  1. Unscrew the BASE from the CHAMBER.

Your Clearomiser should now be in 2 parts.

  1. Run your Clearomiser CHAMBER under a tap to clean any E Liquid from the CHAMBER
  2. Blow into the CHAMBER to release any trapped air or E Liquid.

To reduce mess, place a tissue over the mouth-tip of the Clearomiser whilst blowing into the CHAMBER.

  1. Then blow in the BASE from the bottom (where you would screw onto your Battery).

This will release any trapped air within the BASE.

  1. Dry off your WICK and BASE (which should be screwed together) with a tissue, make sure you do not remove the Rubber Seal “Washer” or damage the wicks by doing this. Please do this gently.
  2. Pour some E Liquid down the side of your Clearomiser, not down the centre tube.
  3. Screw BASE onto CHAMBER, DO NOT over tighten as this will cause damage to both BASE and CHAMBER, only tighten until comfortable.

Notice how the AERIAL Type prong on the WICK sits in the inner centre tube, with the Rubber Seal “Washer” at the moment of this. This Rubber Seal “Washer” acts as a plug, preventing any E Liquid from entering that inner tube.

If your Clearomiser continues to make a bubbling sound, please complete our Returns Form and a member of our Customer Service Team will be in contact with you.

HOW DO I CLEAR MY BASKET?

Please click the below link to clear your basket. You may need to sign in first for this to work.

 

 

http://www.ecignature.co.uk/?clear-cart

0
Connecting
Please wait...
Send a message

Sorry, we aren't online at the moment. Please leave a message and we will get back to as soon as possible. If you can leave as much information as possible this will help us help you as quickly as possible.

* Your name
* Email
* How can we help you?
* Phone
* Subject
Login now

Need more help? Save time by starting your support request online.

* Your name
* Email
* How can we help you today?
* Phone
We're online!
Feedback

Help us help you better! Feel free to leave us any additional feedback.

How do you rate our support?
SIGN UP TO OUR NEWSLETTER
Be the first to receive exclusive offers,discounts and new products only available through our newsletter.
Your Information will never be shared with any third party.
Thank you for the great response to Menthol Blast
Due to popular demand You Can now add me to your Triple Saver And Also to the Twin pack
Subscribe
Be first to receive news and product updates.

Also receive up to 70% off when you sign up to our news letter!

Your Email
2016 (C) All rights reserved.
ALIEN KIT
The Alien kit has a lot of unique features that stand out from the rest of its competitors.
* A high-power mod with a maximum output of 220W
* Large OLED screen
* Micro-USB
* Adjustable airflow tank
£57.99
"This will quickly become your main device because of how easy it is to use"
* Wattage or temperature setting
* Real-time voltage
A premium vape juice that represents creative freedom, a forward-thinking philosophy, and the next evolution of a smoke free lifestyle.
Brand new and designed specifically for European and UK vapers, the 50 watt Smok Q-Box Kit is proof you don’t need a massive mod and tons of power for a compelling vape experience.
QBOX KIT
Smok AIO adopts a pen style design with leak-proof built-in glass tank. Top rotary cap is convenient for a quick no spill refill, 1600mAh battery capacity provides long run time, and the combination of intelligent LED indicator and multiple protections ensures the safety to use.
AIO STICK
The Smok G150 Kit is a Vape Kit which features, 150W Maximum output Power with detailed vaping data displayed on the OLED Display, Coming together with the Smok TFV8 Baby Beast Tank that can hold 2ml of e-liquid, adjustable airflow and top filling system with swivel lock.
G150 KIT
The OSUB 40W Kit from Smok is exquisite, giving 40W output with TC mode. It has a C-shaped magnetic side cover design hiding the fire key connect and Micro-USB charging port. Matched with a 22mm Helmet mini tank it has a top adjustable airflow system, 510 drip tip, top refill system and unique U-shaped e-juice tube. It is super comfortable to both hold and use.
OSUB 40W KIT
OSUB 40W KIT
The smok v8 baby stick kit is a pen style vape kit from Smok, featuring EU TPD Compliancy with a 2ml capacity Smok TFV8 Baby Beast Tank, as well as it simple to use; the Smok Stick V8 battery features 2000mAh capacity battery and various safety protection.
V8 BABY STICK KIT
V8 BABY STICK KIT
LIQUA MIX
PREMIUM VAPE LIQUID
Get ready for a giant burst of tart and sweet in this unique cranberry vape combined with berries, anise, menthol, and eucalyptus.
IN 5 GREAT FLAVOURS
The ergonomic design integrates the all metal fire button on the side for better grip and the industry leading OLED screen with the mode buttons on the side. Enjoy the flavor and vapor out of the variety of GT cores available. Above and Beyond!
REVENGER
REVENGER